2013年1月01日

日产55-50 / 51SN电子功能

正常移位计划

  • 经济模式- Under normal acceleration, the TCM provides earliest possible upshifts and lockup for best economy. Oil pressure is adjusted to provide smooth shifts and engagements.
  • Sport Mode- 如果快速按下加速器并速度超过31英里/小时,则提高换档点以提供最佳性能。降档发生在较低发动机转速下。如果加速器较快移动,则TCM会自动恢复经济模式。
  • 极端模式- 另一种说“踢下来”的方式。当油门踩到地板时,TCM选择用于车速的最低档。
  • 冬季模式- Use the "W" button on the top panel of the gear selector assembly. A warning lamp on the instrument cluster illuminates and the传播从第3档开始,以提供最大牵引力。根据所选档位,可能发生以下情况:
    • D - Starts in 3rd and automatically shifts between 3rd, 4th, and 5th.
    • 4 - 在第3次开始于第3次启动,比D范围内的经济早于经济,第5档锁定。
    • 3 - 在第3次开始,没有UP / DownShifts。
    • L - Starts in 2nd with no up/downshifts.
    • At wide open throttle in winter mode, all gears are used for max performance.
  • 催化转换器开始- 有助于达到工作温度,防止冷却时的转换器锁定和延迟1-2和2-3升档。这是正常功能。
  • Temperature Controlled Lockup- If temperature rises excessively due to heavy load with high ambient temp conditions, the torque converter clutch applies to reduce heat. If temperature drops below 20°C (68°F), lockup is inhibited.
  • 滑倒锁定- Gives smoother lockup and reduces vibration/noise. Computer maintains 50-200 RPM torque converter clutch slip. The following conditions must be met:
    • 换档必须在D,4或3中。
    • 传播must be in 3rd, 4th or 5th.
    • 传输输入速度必须为1100 rpm或更高。
    • 节气门开口必须为35%或更低。
    • Engine coolant must reach certain temperature. Trans oil temperature must be 40°C (104°F), but not exceed 120°C (248°F).NOTE:由于大量转换器离合器滑动,该传动流体的摩擦性能不同。未使用正确的流体会导致传输损坏和代码。
  • Driving Uphill- 为了减少Shift Business,TCM可能在驾驶上坡时稍微改变换档模式。
  • 中立控制- 所有型号都无法使用。TCM在停止时脱离前离合器(CI),施加制动以减少负荷。减少振动/提高燃油经济性。当制动器释放时,向前的离合器接合。必须满足以下条件:
    • 手动换档必须在D,4或3中。
    • 不适用于冬季模式或GEARTRONIC。
    • 变速器油温必须高于10°C(50°F)。
    • Throttle position must be less than 3%.
    • Brake must be pressed.
    • 速度必须为0英里/小时。
    • 发动机速度必须小于I500 RPM。
    • There's a 2 second delay once vehicle has stopped in D, and a 5 second delay from N-D.

Shifting Using Geartronic

当移位器移动到Geartronic时,传动保持在液压“D”位置。当移位器移动到+或 - 位置时,档位选择器模块向TCM发送信号以向上或向下移动传输。驱动程序信息模块将仪表板上的符号从D从D变为所选择的档位,并且信号被发送到档位选择器模块以亮起M并关闭移位器控制台上的其他LED。TCM确定是否可以执行偏移并激活适当的螺线管。TCM在某些情况下覆盖驱动程序的命令。



Nissan Shift Adapts

要清除换档适应,必须使用日产工厂特定扫描仪(Consuard Scan工具)。TCM中的EEPROM被删除并重置为Nissan指的是“TCM初始化”的过程中的默认设置。以下是可以调整的事物列表,必须由TCM学习,以便进行适当的转换和参与感觉:

  • 上/下换档控制- the TCM learns the correct pressure for each shift.
  • N-D订婚- TCM学习正确的前向离合器压力以获得良好的前锋啮合。
  • N-R Engagement- TCM了解正确的直接离合器压力以获得良好的反向接合。
  • 扭矩还原控制- TCM在上下移动期间以及N-D和N-R接合期间,学习正确的发动机扭矩减小,以请求。

此时,无售后市场扫描工具能够执行TCM初始化,也不是有手动重置过程。

请注意:After resetting the shift adapts, the vehicle must be driven 70 to 100 shift cycles through all of the gears at about 20% throttle angle while at operating temperature. This procedure will relearn the shift adapts. Follow the Saturn relearn procedure to relearn the engagements.

日产服务公告#NTBOS-026

更换5速A / T时需要TCM重新编程。
此公告适用于2004-05 Maxima和2005 Altima,具有5速自动变速器。

相关单位


相关零件

虽然Sonnax尽一切努力确保在出版时确保技术文章的准确性,但我们对不准确或可能过时或过时的信息不承担任何责任。